Hi guys Update on HDD failure,i did the test in Ubuntu 14.04 it doesn't show any signs of failure,
here the results.
For now i will run it in Ubuntu till it fails,besides in my opinion ,for me Ubuntu 14.04 better than win 7 or 10,i just stream and browse though ,
i'll keep the good HDD with Win10 Tp installed and will check it out when Win 10 RTM comes out , if MS requires money then screw it, i'll keep free Ubuntu 14.04 very happily.
-----------------------------------------------------------------------
sudo apt-get install smartmontools --no-install-recommends
sudo smartctl -a /dev/sda
------------------------------------------------------------------------
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3320620AS
Serial Number: 9QF78WVQ
Firmware Version: 3.ADG
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Tue Apr 14 00:08:11 2015 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 73) The previous self-test completed having
a test element that failed and the test
element that failed is not known.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 107) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 073 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 097 094 070 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 471
5 Reallocated_Sector_Ct 0x0033 001 001 036 Pre-fail Always FAILING_NOW 57106
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 296546108
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 14608
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 449
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 65535
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 038 045 Old_age Always In_the_past 33 (33 104 34 33 0)
194 Temperature_Celsius 0x0022 033 062 000 Old_age Always - 33 (0 13 0 0 0)
195 Hardware_ECC_Recovered 0x001a 076 045 000 Old_age Always - 225328440
197 Current_Pending_Sector 0x0012 095 094 000 Old_age Always - 116
198 Offline_Uncorrectable 0x0010 095 094 000 Old_age Offline - 116
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 4
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 055 208 000 Old_age Always - 45
SMART Error Log Version: 1
ATA Error Count: 120 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 120 occurred at disk power-on lifetime: 14556 hours (606 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 ae f4 49 e0 Error: UNC at LBA = 0x0049f4ae = 4846766
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 01 ae f4 49 e0 00 04:32:41.155 READ VERIFY SECTOR(S) EXT
42 00 02 ae f4 49 e0 00 04:32:41.146 READ VERIFY SECTOR(S) EXT
42 00 02 ac f4 49 e0 00 04:32:41.130 READ VERIFY SECTOR(S) EXT
42 00 04 ac f4 49 e0 00 04:32:39.878 READ VERIFY SECTOR(S) EXT
42 00 04 a8 f4 49 e0 00 04:32:38.652 READ VERIFY SECTOR(S) EXT
Error 119 occurred at disk power-on lifetime: 14556 hours (606 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 ae f4 49 e0 Error: UNC at LBA = 0x0049f4ae = 4846766
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 02 ae f4 49 e0 00 04:32:41.155 READ VERIFY SECTOR(S) EXT
42 00 02 ac f4 49 e0 00 04:32:41.146 READ VERIFY SECTOR(S) EXT
42 00 04 ac f4 49 e0 00 04:32:41.130 READ VERIFY SECTOR(S) EXT
42 00 04 a8 f4 49 e0 00 04:32:39.878 READ VERIFY SECTOR(S) EXT
42 00 08 a8 f4 49 e0 00 04:32:38.652 READ VERIFY SECTOR(S) EXT
Error 118 occurred at disk power-on lifetime: 14556 hours (606 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 ae f4 49 e0 Error: UNC at LBA = 0x0049f4ae = 4846766
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 04 ac f4 49 e0 00 04:32:41.155 READ VERIFY SECTOR(S) EXT
42 00 04 a8 f4 49 e0 00 04:32:41.146 READ VERIFY SECTOR(S) EXT
42 00 08 a8 f4 49 e0 00 04:32:41.130 READ VERIFY SECTOR(S) EXT
42 00 08 a0 f4 49 e0 00 04:32:39.878 READ VERIFY SECTOR(S) EXT
42 00 10 b0 f4 49 e0 00 04:32:38.652 READ VERIFY SECTOR(S) EXT
Error 117 occurred at disk power-on lifetime: 14556 hours (606 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 ae f4 49 e0 Error: UNC at LBA = 0x0049f4ae = 4846766
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 08 a8 f4 49 e0 00 04:32:41.155 READ VERIFY SECTOR(S) EXT
42 00 08 a0 f4 49 e0 00 04:32:41.146 READ VERIFY SECTOR(S) EXT
42 00 10 b0 f4 49 e0 00 04:32:41.130 READ VERIFY SECTOR(S) EXT
42 00 10 a0 f4 49 e0 00 04:32:39.878 READ VERIFY SECTOR(S) EXT
42 00 20 a0 f4 49 e0 00 04:32:38.652 READ VERIFY SECTOR(S) EXT
Error 116 occurred at disk power-on lifetime: 14556 hours (606 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 ae f4 49 e0 Error: UNC at LBA = 0x0049f4ae = 4846766
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 10 a0 f4 49 e0 00 04:32:36.061 READ VERIFY SECTOR(S) EXT
42 00 20 a0 f4 49 e0 00 04:32:36.060 READ VERIFY SECTOR(S) EXT
42 00 20 80 f4 49 e0 00 04:32:36.058 READ VERIFY SECTOR(S) EXT
42 00 40 80 f4 49 e0 00 04:32:39.878 READ VERIFY SECTOR(S) EXT
42 00 40 40 f4 49 e0 00 04:32:38.652 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short captive Completed: unknown failure 90% 14546 16453020
# 2 Short offline Completed: unknown failure 90% 14546 325795665
# 3 Short offline Completed: unknown failure 90% 14546 171868828
# 4 Short offline Completed: unknown failure 90% 14388 33069049
# 5 Short captive Completed: unknown failure 90% 14388 16453020
# 6 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
